1
Säljes / SV: Förgasarturbo och trim..
« skrivet: september 27, 2012, 13:32:31 »
skicka PM til rsport forgaser (excuse my swedish)
300power.com - Forum
Nyheter:
300power dekalen finns nu att köpa på Dekaltrim.nu.
Klicka på Klubbar och sen 300_power.(300power medlemmar har 15 % rabatt)
Visa inlägg
Denna sektion låter dig visa alla inlägg som denna medlem har skrivit. Observera att du bara kan se inlägg i områden som du har tillgång till.
Sidor: [1]
2
Projekt / SV: Volvo 360 -87 3d Suget var förstort. Bilder hjulupphängning 240delar
« skrivet: december 21, 2011, 12:21:02 »
Have you got a picture from the lower shock mount?
If I understand correct you still use the 360 gearbox and axles but use the 240 rear trailing arms instead of the leaf springs?
Don't you need at least a panhard bar/rod with this setup?
If I understand correct you still use the 360 gearbox and axles but use the 240 rear trailing arms instead of the leaf springs?
Don't you need at least a panhard bar/rod with this setup?
3
Köpes / Volvo 360 L-jet ecu/computer
« skrivet: november 24, 2011, 16:34:26 »
Hi,
Looking for a Volvo 360 ecu/ l-jet computer.
Please contact me if you have anything for sale at a reasonable price (student budget).
Tank!
MVH,
Ruben
Looking for a Volvo 360 ecu/ l-jet computer.
Please contact me if you have anything for sale at a reasonable price (student budget).
Tank!
MVH,
Ruben
4
Projekt / SV: Sugtrimmning av vinterbilen! Nu med film!
« skrivet: november 01, 2011, 13:34:44 »
That´s a really thick spring coil. Will you be using just one spring, cut it in half?
I've been looking at ebay but I do find them rather expensive. Biltema might be a good option.
Is it thise one: http://www.biltema.se/sv/Bil---MC/Stotdampare-Fjadersystem-och-Hjul/Spiralfjader/Ford/Scorpio/67329-SPIRALFJADER-FORD-SCORPIO-BAK/
Saw you wrote down the article number, so it must be the ones in the link:) Looks like a good option.
I've been looking at ebay but I do find them rather expensive. Biltema might be a good option.
Is it thise one: http://www.biltema.se/sv/Bil---MC/Stotdampare-Fjadersystem-och-Hjul/Spiralfjader/Ford/Scorpio/67329-SPIRALFJADER-FORD-SCORPIO-BAK/
Saw you wrote down the article number, so it must be the ones in the link:) Looks like a good option.
6
Köpes / Volvo 360 ECU
« skrivet: oktober 27, 2011, 00:39:45 »
Looking for a cheap Volvo 360 ecu.
Would like to try to change the injection settings by changing some resistors in the ecu.
Looking for a cheap ecu to experiment with.
Would like to try to change the injection settings by changing some resistors in the ecu.
Looking for a cheap ecu to experiment with.
7
Drivlina/Växellåda / Stronger clutch and pressureplate (B14+T)
« skrivet: januari 23, 2011, 11:24:02 »
Which options do I have if I need a stronger clutch and pressurplate for my B14?
My small +T project is almost finished. At least steg 1.
B14.4, NA B14 cam, which looks like it might work pretty good in a turbo setup
Nice U-pipe
IC
R5 turbo renix
Garrett T3 45 trim compressor, .37 turbine
LPG only
With this setup I would like to see 150 whp at moderate boost levels.
In the future I would like to make in intake manifold myself, fit a regring cam, some portwork, better turbo (some versions of the HX30 might work nice), bigger ic. 200whp should be possible.
Looks like there is a solution to the alu propshaft problem.
Because of these plans I will need a stronger clutch quite soon I guess. Don't see the stock parts hold 150 whp. I also have purchased a new OEM kit which can be reinforced. This (reinforcing)is unfortunately quite expensive (E200-250 for the pressure plate alone) and I still need a stronger clutch.
Does anyone know an affordable setup? Another question I have, is it possible to lighten a stock B14 flywheel?
Have heard that a 1.7 clucth might fit or a fiat uno turbo 4-puck (don't like 4 pucks).
My small +T project is almost finished. At least steg 1.
B14.4, NA B14 cam, which looks like it might work pretty good in a turbo setup
Nice U-pipe
IC
R5 turbo renix
Garrett T3 45 trim compressor, .37 turbine
LPG only
With this setup I would like to see 150 whp at moderate boost levels.
In the future I would like to make in intake manifold myself, fit a regring cam, some portwork, better turbo (some versions of the HX30 might work nice), bigger ic. 200whp should be possible.
Looks like there is a solution to the alu propshaft problem.
Because of these plans I will need a stronger clutch quite soon I guess. Don't see the stock parts hold 150 whp. I also have purchased a new OEM kit which can be reinforced. This (reinforcing)is unfortunately quite expensive (E200-250 for the pressure plate alone) and I still need a stronger clutch.
Does anyone know an affordable setup? Another question I have, is it possible to lighten a stock B14 flywheel?
Have heard that a 1.7 clucth might fit or a fiat uno turbo 4-puck (don't like 4 pucks).
8
Trimning / B19 46/38mm ventiler, will it fit?
« skrivet: augusti 19, 2010, 23:04:28 »
Hi,
Sorry for my lacking Svenska.
I have a very low klm B19. It is near to new.
Because the B19 has such a small bore I wonder if a head with bigger valves (46mm insug and 38mm avgas) would work? Would they touch the bore?
I know the 530 head already hangs over the bore.
I'd much rather use my extremely fresh B19 and work on that than using a B230 with 300k klm and has a lot of piston slap.
Hope someone will be able to shed some light.
Sorry for my lacking Svenska.
I have a very low klm B19. It is near to new.
Because the B19 has such a small bore I wonder if a head with bigger valves (46mm insug and 38mm avgas) would work? Would they touch the bore?
I know the 530 head already hangs over the bore.
I'd much rather use my extremely fresh B19 and work on that than using a B230 with 300k klm and has a lot of piston slap.
Hope someone will be able to shed some light.
10
Säljes / SV: Grenrör turbo och downpipe till 360, nu med BILDER!
« skrivet: september 23, 2009, 20:27:38 »
I send you a PM. I'd like to get a shipping quote to the Netherlands.
Thanks.
Thanks.
11
WANTED / Whiteblock/vitmotor in V360
« skrivet: september 17, 2009, 04:28:18 »
Has anyone put a 4/5 cyllinder whiteblock in a Volvo 360. I know someone on V3M is building a 300 with whiteblock.
Have others done it? Which set backs/hurdles have you taken?
Has anyone who has done this drawings from the enginemounts?
Cheers,
Ruben
Have others done it? Which set backs/hurdles have you taken?
Has anyone who has done this drawings from the enginemounts?
Cheers,
Ruben
12
Säljes / SV: Glasfiberhuv volvo 360
« skrivet: september 15, 2009, 01:25:03 »
Any idea if you could get it shipped safely to the Netherlands?
Sidor: [1]